config:remotecontrol:dhd
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
config:remotecontrol:dhd [2017/11/24 12:28] – [Monitor] tw | config:remotecontrol:dhd [2019/10/04 12:47] – [General] tw | ||
---|---|---|---|
Line 3: | Line 3: | ||
This article covers remote control of mAirList with digital broadcast consoles from [[http:// | This article covers remote control of mAirList with digital broadcast consoles from [[http:// | ||
- | The information in this article is current as of: mAirList 5.2 beta | ||
===== Supported Hardware ===== | ===== Supported Hardware ===== | ||
Line 9: | Line 8: | ||
The DHD remote control interface in mAirList supports the following consoles from DHD: | The DHD remote control interface in mAirList supports the following consoles from DHD: | ||
- | * Series 52 (all models: 52/MX, 52/RX, 52/SX, 52/DX, 52/ | + | * Series 52 (all models: 52/MX, 52/RX, 52/SX, 52/DX, 52/ |
* RM4200D | * RM4200D | ||
* RM3200D | * RM3200D | ||
- | Note: The RM2200D | + | For the RM2200D, see [[dhd2200|here]]. |
===== Configuration ===== | ===== Configuration ===== | ||
Line 49: | Line 48: | ||
Note: The XP5 XML format is not documented and not officially supported by DHD. We did our best to parse the file and extract all relevant information. But future Toolbox versions may change the format of the XP5 files without notice. If your XP5 file fails to load, in particular after an update of the DHD Toolbox application, | Note: The XP5 XML format is not documented and not officially supported by DHD. We did our best to parse the file and extract all relevant information. But future Toolbox versions may change the format of the XP5 files without notice. If your XP5 file fails to load, in particular after an update of the DHD Toolbox application, | ||
+ | |||
+ | <WRAP center round tip 60%> | ||
+ | Starting with mAirList 6.2.3, the XP5 file is only used for the //DHD Console// window. Automatic configuration of fader channels and logics is done using the Extended Audio and Logic ID export from Toolbox (see next paragraph). | ||
+ | </ | ||
+ | |||
+ | ==== Toolbox Import (mAirList 6.2.3 and up) ==== | ||
+ | |||
+ | tbd | ||
+ | |||
==== Players ==== | ==== Players ==== | ||
Line 238: | Line 246: | ||
Data0, Data1, Data2, Data3, Data4, Data5, Data6, Data7: byte); | Data0, Data1, Data2, Data3, Data4, Data5, Data6, Data7: byte); | ||
begin | begin | ||
+ | end; | ||
+ | |||
+ | … where {{: | ||
+ | |||
+ | * '' | ||
+ | * '' | ||
+ | * '' | ||
+ | * '' | ||
+ | |||
+ | So in this example … | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | … a query for the highlighted data packet might look like this: | ||
+ | |||
+ | procedure OnDHDCommand(Remote: | ||
+ | Data0, Data1, Data2, Data3, Data4, Data5, Data6, Data7: byte); | ||
+ | begin | ||
+ | if (ID = $01F3FFFF) AND (Data0 = 0) AND (Data1 = 15) AND (Data2 = 0) then begin | ||
+ | // do something | ||
+ | end; | ||
end; | end; | ||
config/remotecontrol/dhd.txt · Last modified: 2019/10/28 06:22 by tondose